Lintel Type : Cavity Lintels
Cavity Width : 150-165mm
Lintel Duty : Standard Duty
Thermally Broken : No
Wide Inner Leaf? No
Catnic
Become a trade card holder and get a discount on this item
Pickup available at Tipton West Midlands
Usually ready in 4 hours
The Catnic CG150/100 standard duty cavity wall lintel is designed for masonry cavity walls with a 150–165mm cavity, a 100–115mm inner leaf and a 100–102mm outer leaf. Its open-back steel profile allows masonry to be built up continuously on both leaves, while integral insulation, a built-in DPC and plaster key provide additional practical features. Wade supplies the CG150/100 in 12 lengths from 900mm to 3600mm, with safe working loads of 15–26kN depending on length.
Designed for cavity widths of 150–165mm, with a 100–115mm inner masonry leaf and a 100–102mm outer leaf.
Suitable for specified masonry, timber floor and roof loading applications within Catnic's published load capacity.
Allows masonry to be built up continuously on both the inner and outer leaves during construction.
Incorporates a damp-proof course. Additional DPC may be required depending on installation and exposure conditions.
Supplied with continuous insulation to help reduce cold bridging and an integral plaster key to assist finishing.
Manufactured from galvanised steel with Catnic's protective black polyester powder coating.
| Manufacturer | Catnic |
|---|---|
| Product code | CG150/100 |
| Lintel type | Standard duty cavity wall lintel |
| Cavity width | 150–165mm |
| Inner leaf | 100–115mm |
| Outer leaf | 100–102mm |
| Available lengths | 900–3600mm, with 12 sizes available from Wade |
| Manufacturer's length range | 750–3600mm |
| Nominal end bearings | 150mm at each end |
| Safe working load | 15–26kN, depending on length |
| Built-in DPC | Yes. Additional DPC may be required in some situations. |
| Plaster key | Integral |
| Insulation | Integral insulation |
| Finish | Galvanised steel with black polyester powder coating |
The Catnic CG150/100 has different safe working loads depending on length. The following table covers the lengths currently available from Wade.
| Lintel length | Safe working load |
|---|---|
| 900–1500mm | 15kN |
| 1650–1800mm | 18kN |
| 2100mm | 20kN |
| 2400mm | 22kN |
| 2700–3600mm | 26kN |
The CG150/100 is intended for standard-duty masonry cavity walls with a cavity width of 150–165mm. It supports typical masonry loads and specified timber floor and roof loads, subject to the manufacturer's published loading conditions.
The lintel's open-back profile allows masonry to be built up continuously on the inner and outer leaves and is suitable for fair-faced inner leaf masonry.
Catnic specifies nominal 150mm end bearings at each end. The required lintel length is therefore normally determined by adding 300mm to the structural opening width.
For example, a 1200mm opening would normally require a 1500mm lintel. The selected lintel must also have sufficient safe working load for the intended construction.
Ensure the wall dimensions and supporting masonry are suitable for the selected lintel. Follow Catnic's installation guidance and the project structural design, including any temporary propping or additional damp-proofing requirements.
For a narrower cavity, Wade also supplies the Catnic CG90/100 standard duty cavity lintel, designed for 90–105mm cavities.
Browse Wade's cavity lintel collection to compare other available models and wall dimensions.
The CG150/100 is designed for cavity widths of 150–165mm, with a 100–115mm inner leaf and a 100–102mm outer leaf.
Wade supplies 12 lengths from 900mm to 3600mm. Catnic's full manufacturing range starts at 750mm.
The published safe working load ranges from 15kN to 26kN, depending on lintel length. Refer to the loading table above and Catnic's technical datasheet for the applicable rating and loading conditions.
Yes. The CG150/100 incorporates a built-in damp-proof course. Additional damp-proofing may be required depending on installation and exposure conditions.
Yes. The CG150/100 incorporates an integral plaster key to assist plaster finishing.
Catnic specifies the CG150/100 for typical masonry, timber floor and roof loads, provided the actual loading conditions fall within the selected lintel's design capacity.
Overall rating: 4.5 / 5 from 6 reviews.
Amazing and perfect. Professional and the products are top quality. Delivery said 3-5 working days but as soon as they understood they couldn't deliver in that time frame they kept me updated straight away and told me a more realistic timescale. Would definitely order again
Very good service, ordered some Cavity Closers a few days later...just arrived Thanks Peter
1650mm lintel with 470mm insulation missing from inside
Excellent website. Navigates well. Item arrived when they said it would. Good service all round.
Great value and delivery on time!
Great prices, prompt delivery and great to be able to speak to someone to clarify details as well. 5*
trade with wade
Apply for a Trade Card today to save money on your purchases and to receive exclusive discounts. Signing up is quick and easy.
Your basket is currently empty.
Start Shopping
